Skip to Content

Liftmaster Error Code 1-5 [How to Fix]

Liftmaster Error Code 1-5 [How to Fix]

Liftmaster Error Code 1-5 – Liftmaster offers a complete and combined solution for door automation for both industrial and residential buildings. 

Complaints of Liftmaster error 1-5 are not that rare when you browse online forums. Error code 1-5 on Liftmaster occurs when no RPM is detected in the first second of movement. 

In this case, your door moves 15-20 cm stops or reverses, or has no movement, and only a single click or the opener hums for 1-2 seconds with no movement. 

So, to get rid of this error code, keep on reading the article to know how to fix the 1-5 error code on Liftmaster. 

How to Fix: Liftmaster Error Code 1-5

Liftmaster error 1-5 is technically referred to as a “motor control” error and there are a few reasons why you are facing this error code. 

When you activate the garage door opener by pressing the wall button, the opener will respond in one of four ways:

  1. The garage door travels less than 6-8 inches, stops, and/or reverses
  2. The garage door does not move, hums for less than 5 seconds 
  3. The garage door does not move, hums for more than 5 seconds
  4. The garage door does not move, only clicks 

You can fix this problem by the following solutions:

Remove Obstruction

Sometimes the door moves 15-20 cm and then stops or reverses. In this case, you can manually open and close the door. Or you can check for binding or obstructions like door lock or broken spring. 

Moreover, you’ll also need to check wiring connections at the travel module and at the logic board. If necessary, it is better to replace the travel module. 

No Movement, only a Single Click

If there is no movement of your door, you can manually open and close the door or check for obstructions or binding like a door lock or broken spring. And if required, replace the logic board. 

Opener Hums for 1-2 seconds No Movement 

If the opener hums for 1-2 seconds and there is no movement, check for obstructions or binding or try to manually open and close the door. 

However, since it is a malfunction that cannot be repaired without exchanging the motor control module, you can replace the motor if necessary. 

Contact your Near Dealer 

If you are inexperienced and do not know how to segregate the defective components, it is always better to take the help of your nearest dealer. To locate dealers near you, visit this page

Contact Liftmaster 

Finally, the last thing you can do about the Liftmaster error 1-5 is to get in touch with Liftmaster’s customer support. So, visit here and connect to the customer service. 

Final Words: When you face error code 1-5 on Liftmaster, it means that RPM is not detected in the first second of movement. 

Ideally, you can easily fix this issue by manually opening or closing the door or removing any obstruction like a broken spring. We hope the above solutions have helped you to fix the Liftmaster error code 1-5 easily. 

FAQs

What is error code 1-5 on Liftmaster?

Error code 1-5 on Liftmaster occurs when no RPM is detected in the first second of movement. 

How do you clear Liftmaster error code 1-5?

Generally, you can easily fix this issue by manually opening or closing the door or removing any obstruction like a broken spring or door lock.

How do I reset my garage door opener?

Locate the learn button on the control panel, and press and hold the Learn button till the LED light turns off. By doing so, it’ll reset the opener and delink the keypad and nay remote controls that you earlier set to operate the garage opener. To let you know that it is successful, the light built inside the opening unit will flash. 

How do I troubleshoot my Liftmaster garage door opener?

Check if the batteries in the remote control are required to be replaced, if the springs are broken or if the door required lubrication. 

Liftmaster Error Code 4-1 [How to Fix 2022]
Liftmaster Error Code 4-2 [How to Fix]
Liftmaster Error Code 4-3 [How to Fix]
Liftmaster Error Code 4-6 [How to Fix]